@prefix prodottidellaricerca: . @prefix istituto: . @prefix prodotto: . istituto:CDS052 prodottidellaricerca:prodotto prodotto:ID264365 . @prefix pubblicazioni: . @prefix unitaDiPersonaleInterno: . unitaDiPersonaleInterno:MATRICOLA6183 pubblicazioni:autoreCNRDi prodotto:ID264365 . unitaDiPersonaleInterno:MATRICOLA8031 pubblicazioni:autoreCNRDi prodotto:ID264365 . unitaDiPersonaleInterno:MATRICOLA1307 pubblicazioni:autoreCNRDi prodotto:ID264365 . unitaDiPersonaleInterno:MATRICOLA6558 pubblicazioni:autoreCNRDi prodotto:ID264365 . @prefix unitaDiPersonaleEsterno: . unitaDiPersonaleEsterno:ID21450 pubblicazioni:autoreCNRDi prodotto:ID264365 . unitaDiPersonaleEsterno:ID16323 pubblicazioni:autoreCNRDi prodotto:ID264365 . unitaDiPersonaleEsterno:ID21590 pubblicazioni:autoreCNRDi prodotto:ID264365 . @prefix modulo: . modulo:ID2162 prodottidellaricerca:prodotto prodotto:ID264365 . unitaDiPersonaleInterno:MATRICOLA14988 pubblicazioni:autoreCNRDi prodotto:ID264365 . unitaDiPersonaleInterno:MATRICOLA11244 pubblicazioni:autoreCNRDi prodotto:ID264365 . @prefix rdf: . prodotto:ID264365 rdf:type prodotto:TIPO1305 . @prefix retescientifica: . prodotto:ID264365 rdf:type retescientifica:ProdottoDellaRicerca . @prefix rdfs: . prodotto:ID264365 rdfs:label "High quality 3C-SiC/Si grown on an optimized SiC buffer layer (Abstract/Comunicazione in atti di convegno)"@en . @prefix xsd: . prodotto:ID264365 pubblicazioni:anno "2013-01-01T00:00:00+01:00"^^xsd:gYear . @prefix skos: . prodotto:ID264365 skos:altLabel "
Matteo Bosi, Giovanni Attolini, Marco Negri, CESARE FRIGERI, Elisa Buffagni, Claudio Ferrari, Tiziano Rimoldi, Luigi Cristofolini, Lucrezia Aversa, Roberta Tatti, Roberto Verucchi (2013)
High quality 3C-SiC/Si grown on an optimized SiC buffer layer
in HeteroSic-WASMPE 2013, Nizza (F), 17-19 giugno 2013
"^^rdf:HTML ; pubblicazioni:autori "Matteo Bosi, Giovanni Attolini, Marco Negri, CESARE FRIGERI, Elisa Buffagni, Claudio Ferrari, Tiziano Rimoldi, Luigi Cristofolini, Lucrezia Aversa, Roberta Tatti, Roberto Verucchi"^^xsd:string ; pubblicazioni:titoloVolume "Book of Abstracts"^^xsd:string ; skos:note "Abstract"^^xsd:string ; pubblicazioni:affiliazioni "1 IMEM-CNR Institute Parco Area delle Scienze 37 A, 43010 Parma (Italy)\n2 Dipartimento di Fisica e Scienze della Terra, Universit\u00E0 degli Studi di Parma, I-43124 Parma, Italia\n3 IMEM-CNR, Via alla Cascata 56/C, 38123 Trento, Italy"^^xsd:string ; pubblicazioni:titolo "High quality 3C-SiC/Si grown on an optimized SiC buffer layer"^^xsd:string ; prodottidellaricerca:abstract "We describe a procedure for the optimization of a 3C-SiC buffer layer for the deposition of 3C-SiC / (001) Si. After a standard carbonization at 1125 \u00B0C, we deposited a 100 - 150 nm thick SiC buffer with varying SiH4 and C3H8 flow rates at 200 mbar, while the temperature was increased from 1125 \u00B0C to the growth temperature of 1380 \u00B0C. Different heating rates and precursor flows were tested, which influenced the quality and the crystallinity of the buffer layer and the presence of voids at the SiC/Si interface. The buffer layers were studied by stopping the growth at 1380 \u00B0C, just before thick SiC film growth, and analyzed by Atomic Force Microscopy (AFM), Scanning Electron Microscopy (SEM), Raman,Transmission Electron Microscopy (TEM), X-Ray- Photoelectron Spectroscopy (XPS) and X-Ray Diffraction.\nBy the optimization of the growth conditions, in particular by using a slow heating ramp (21.5 \u00B0C / min) and higher precursor rate, interfacial voids were greatly reduced (fig.1) and the crystallinity was improved, with the appearance of a (002) SiC peak in the XRD spectra with FWHM of about 1400 arcsec.\nTo demonstrate the effectiveness of the described procedure, on the optimized buffer (labeled B in fig. 1) a high-quality 1.5 ?m 3C-SiC was grown using SiH4 and C3H8 with Si/C=1.4 at 1380 \u00B0C and 200 mbar, with excellent surface morphology (roughness < 1 nm on 1x1 ?m2 scale) as measured by AFM, good crystallinity as measured by XRD (FWHM of about 790 arcsec), XPS and TEM (fig. 2) and low stress, as indicated by Raman measurements: considering the positions of the LO and TO peaks in the film compared to the bulk we calculated a residual tensile strain of about 0.03%."@en ; prodottidellaricerca:prodottoDi modulo:ID2162 , istituto:CDS052 ; pubblicazioni:autoreCNR unitaDiPersonaleEsterno:ID16323 , unitaDiPersonaleInterno:MATRICOLA14988 , unitaDiPersonaleEsterno:ID21450 , unitaDiPersonaleInterno:MATRICOLA6183 , unitaDiPersonaleInterno:MATRICOLA11244 , unitaDiPersonaleInterno:MATRICOLA8031 , unitaDiPersonaleEsterno:ID21590 , unitaDiPersonaleInterno:MATRICOLA6558 , unitaDiPersonaleInterno:MATRICOLA1307 . @prefix parolechiave: . prodotto:ID264365 parolechiave:insiemeDiParoleChiave . parolechiave:insiemeDiParoleChiaveDi prodotto:ID264365 .